I’m planning on building a PC soon and, while I have done plenty of research, I’d like to hear advice from people who have experience in the area personally. It’s also just nice talking to other people in general, lol
You must log in or # to comment.
I would absolutely use “PC Part Picker” because as you assemble the various components, that site will tell you if there are incompatibilities. For instance whether a power supply will fit in the case.
And if you don’t have someone to bounce ideas off of, this is a pretty good site that was recommended to me to help narrow your choices.
I second Logical Increments, it’s great.
deleted by creator
Don’t skimp on the power supply brand. Buy a reputable one. Buy one with headroom if you plan on upgrading your GPU at a later time.
Watch some build videos from tech YouTubers and watch the steps they go through.
For gaming start with the GPU and build around it. Pick a CPU with a reasonable price that will not bottleneck it. YouTube reviews are your friend here. Watch a few with your CPU and GPU pairing and get an idea of the average and one percent low marks.
For your first PC, stick to air cooling. Pick a reputable brand.
I personally like gamersnexus reviews for all the parts you can. They are very methodical with benchmarks. Ask questions here as you will have many.
You may be building a PC for a use case other than gaming. If that’s the case you may want to pick another part to start your build around. For instance, developers have a different workload compiling code and would focus more on CPU and threaded workloads.
Basically know your use case, budget, and ask specific questions as you learn from videos and the community will help you produce a great result.
Save everything that comes in your motherboard box. Don’t be the fool (me) who needs to buy m.2 screws on Amazon.
I end up saving everything from every box, haha. I still have all the cords from my modular PSUs sitting in my basement, still in their little bags
Don’t forget to buy thermal paste!
Also don’t forget to remove the plastic film(s) they put on the CPU/Cooler and everywhere else!
Most coolers come with it preapplied these days, but it’s still good to have in case you need to reseat your cooler.
Slightly different advice from what others have said, but while building it, I’ve always used an anti static wristband, grounded to either ground or the pc case. Maybe I’m overly paranoid, but that’s what I was taught, and haven’t had any issues with ESD so far
You really can’t go wrong with https://pcpartpicker.com/. Obviously double check things like GPU size mentioned below, and up size your PSU if you ever intend to upgrade GPU in same case. 850 Watts is a solid choice regardless of what your current picks need.
Buy more than you need, is the lesson I’ve learnt. Especially power, I have an 850 as well, but I sort of wish I bought a 1000W, the way things are going.
5950x with 7900xtx runs fine on my 850 watt.
For sure, I win a 5800x3d and a 4070ti on an 850, but I had to replace the 650 that I built with in 2020 to do that. Two power supplies in three years could have been averted if I had just bought a bit more than I needed the first time. It sucks having to completely rewire an already built computer too.
If you can, just pick the parts but don’t build it yourself, ask a friend who knows what he’s doing and watch or pay for it. You really really don’t want to screw it up with these GPU and CPU prices.
I would, but unfortunately I don’t know anyone with experience in this area. But I won’t be doing it by myself, and I’ve done quite a bit of research, so I at least think I won’t mess up to the point of breaking anything
The site from which you buy your components doesn’t propose you to pay for assembly ?
No, sadly. Besides, I don’t know if I would go with that option even if it was. I’ve been wanting to build my own PC for a while and I am willing to run the risk, although it would be nice to have somebody with experience help
It’s fairly safe to just do it yourself. Simply be aware you don’t have to force anything too much. Pushing the ram into the slots is likely the most force you need. Even if you get something wrong as long as you didn’t apply to much force and break some pins you can just reseat it and try again.
CPU is the one you’re most likely to mess up but that takes virtually no force at all. If you’re using basically any force, stop and turn it because you clearly don’t have it lined up correctly. They should drop in and then lock into place.
If building it is of interest to someone I think anyone can do it. If you don’t know, just stop a check a youtube video but these days it’s fairly easy to do and virtually impossible to plug anything into the wrong spot.
I highly recommend PC Partpicker for compiling all your components (although I don’t typically follow the listed purchase links). The comparability checker it has can save some real headaches!
Otherwise, some general advice:
-
Remember the motherboard standoff screws. Most cases these days have them pre-installed, but my first rig did not. And I bent the mobo a little bit before realizing my mistake. It still worked in the end, but it’s now my #1 cautionary tale about PC Building.
-
Do yourself a favor, and make an attempt at proper cable management. It’ll make replacing components so much easier down the line.
-
Get a fully modular PSU (if in your budget). This will help with #2 above immensely.
-
Read the manual that comes with your motherboard. It usually has a lot of guidance for assembling the computer, especially if this is your first time.
-
Have fun! PC Building/Gaming is one of my favorite hobbies, and I’m always glad to see new people getting interested in it!
Good luck, and don’t be afraid to ask questions!
This is all spot on advice. The motherboard and case manual should be open and nearby as you build the pc.
-
Lota of great advice here but my must have is a tray to put all the screws and other small bits. Far too easy to lose stuff. iFixit do a good one but you can find an equivalent lying around im sure.
https://pcpartpicker.com/ or https://pcpartpicker.ca if you’re Canadian is very helpful for drafting up a build or shopping for parts, specially if you’re a newbie. You can even find recommended builds on there.
If you plan on doing anything with linux fuck nvidia. It’s such a PITA. Biggest regret of my build.
Trust me, I know (I tried running Linux on my current NVDIA PC… Never again). While I plan on running Windows (mainly due to how much support it has for like. Everything) I do plan on running Linux on a laptop in the future and possibly dual booting
I love dual booting. If I need to quickly check mails or search the web linux launches in an instant. If I need to game I dont care about longer boot time anyhow.
Yeah, that’s why I wanna dual boot myself, except there’s some software I need on Windows that isn’t available on Linux along with games. Also, what distro(s) do you use? I’ve already picked out a few candidates for what I’ll use, but it’s nice hearing firsthand experiences
I’ve been using Debian because it’s easy to use basically. But it’s no good for tinkering. It takes ages for packages to get moved into the stable channel and testing is exactly that and causes headaches. But if you want a stable and easy to use OS Debian is great. Set it up once and you’re set for a long time.
But I like to tinker so there is a clutter of packages I’ve installed but don’t use and I’ve lost track of them and the configs. It runs but needs cleaning up (again).
Which is why I’m going to switch to Guix. I’m hoping to replicate the same basic set up on my laptop and desktop with only minor differences. Guix allows the declaration of the entire system and if you use the same file it will always be set up exactly the same way. Plus the fact that I can roll back the entire system to a previous state sounds really appealing for someone who likes to break stuff. That said the declaration files and anything to do with Guix itself uses Lisp and as a lisp noob I’m expecting a lot of headaches and tabbing to the manual. Also package installation and so on seems rather unintuitive but the manual is well written and exhaustive. It’s more of an adventure for sure but the OS is stable and ready to use out of the box.
Ooo never heard of Guix, just did a little research on it. I am looking to switch to a declarative distro as well. I seem to have the same tendency of breaking shit when playing around with different packages and running different projects locally. I have been looking at NixOS, have you heard of it and if so, why did you choose GUIX over it?
I’ve never heard of Guix before! From what the official page tells me it seems like a pretty in-depth os, and I wish u luck with it!
For the love of GOD the first thing you should install is the motherboard back plate.
Spoken from traumatic experience.
This is why building outside of the case first is a good idea 😂
There’s usually no need to buy the top end motherboards, they have a whole lot of bells and whistles you won’t ever miss.
There’s not too places you can damage things when installing, but I think the most understated one is the USB 3.0 header that you connect from the case to the motherboard. The plug is super tight and very difficult to remove once you put it in, so I recommend only plugging it in once you’re ready to start using your machine. I know too many stories of people breaking it and not being able to plug in USB devices to the front of their PC case because of this.
Before mounting your motherboard, double-check the number of screws/standoffs you need, then make sure all the standoffs match up with the holes in the motherboard.
I misaligned one once and shorted out a motherboard.
